Mike's 1968 Ford Mustang

valleyfirearms's Homepage >> Pictures >> Mike's 1968 Mustang Overhaul

Mike's 1968 Mustang Overhaul

GTsidestripe 1	settlers bay	settlers bay1	settler bay2	installing my 9 inch	putting the brakes o...
remove 8 inch rear e...	new work platform	trunk after	lined trunk with bit...	bituthane and underc...	new shelby style gri...
carpet after dye	dying carpet	the first cruise aft...	sitting at the end o...	end of drive	finished dash
not quite finished	installed widshield ...	all new rubber weath...	stripped out dash ge...	cleaned up interior	new rubber
after sitting in pai...	installing trim and ...	BEFORE AND AFTER	new paint	new paint front view	new paint 2
rear view bad ass!!...	GT500 tail panel	top view	trunk area	front view 2	paint
masked	tail before panel	almost finished with...	painting the stripes	0 MUSTANG 1 118	laying out the strip...
painting the base co...	white tint primer	sealing the door jam...	just before paint	ready for base coat	sealed before base c...
load up for paint	wet sanding!	more wet sanding	primer coat	primer coat 1	sealer
sealer1	wash and condition b...	trunk corner after s...	matching surfaces	making gaps uniform ...	fabricated sheetmeta...
close up of fabricat...	rear view	re built 9" w / 4:11...	68 tail panel and GT...	sequential LEDs for ...	making new lines
working on lines	fitting the extensio...	aligninging the deck...	passenger side quart...	driver's side quarte...	inside of trunk qu...
four bolts holding o...	fitting deck lid and...	fitting	epoxy bolts onto bac...	sand and skim coats ...	cleaned out
rust in the corner p...	after repair	tack weld patch and ...	in the shop	corner of trunk befo...	whitechopia9o1
whitechopia9o	9 inch rear housing ...	body prep trunk area	quarter panel prep	upper corner trunk/q...	removal of windshiel...
rocker repair	sanding	door rubber	whitechopia9	silverchoppy5	bluechopqw9
fitting the fibergla...	fitting fiberglass h...	fiberglass hood	fiberglass deck lid	fiberglass deck lid ...	$100 9
ford 9"	ford 9" close up	New 210cc aluminum h...	new valve covers	new flip open GT gas...	new GT500 tail light...
new GT500 deck lid	new cowl hood	R valance	original 1968 vintag...	I had to weld the ho...	monto carlo bar
me cleaning the wind...	new frame rail	frame rail after rep...	modify frame rail fo...	working on drilling ...	the old frame rail d...
getting the frame ra...	top side of frame ra...	rear frame rail wher...	finding the spot wel...	new 18's	3 weeks of rain so I...
passenger side front...	passenger side splas...	new front	new fender	remove surface rust ...	clean and kill any r...
replacing hinge pins...	photo shop41	messing around with ...	passenger side87	NEW WHEELS91	drivers side torque ...
torque box roughed i...	drivers side torque ...	drivers side torque ...	finished drivers sid...	spray on undercoatin...	bottom of torque box
front of torque box ...	sandblast	sandblasted all area...	frame repair35	frame repair	frame rail after cle...
It apears this torqu...	of course the frame ...	Years of rust and ro...	passenger torque box...	remove the passenger...	making shims to adju...
passenger quarter pa...	stripping the paint	before new weld	me grinding the old ...	Passenger side quart...	Drivers side quarter...
Cut and weld bottom ...	Bottom of quarter pa...	cold zinc	holes after MIG gett...	holes from old exhau...	Sealing the inner lo...
Top quarter panel ro...	Drivers fender rough...	Weld and grind	It wasnt hard to fin...	thank goodness for g...	Im not a welder as y...
door3349	door88	front lower corner o...	drivers side fender9	FUBAR but I fixed it...	remove fender for ma...
body work	hood after stripping...	passenger door68	cut the rust from th...	stripping the paint ...

Sort By

Display

Mike's 1968 Ford Mustang